STATUS_NO_IP_ADDRESSES (0XC00002F1) Fix: No IP on Local Machine

When You'll See This Error

You're working away, then boom—your machine loses all network connectivity. You try to access a shared drive or browse the web, and you get the error STATUS_NO_IP_ADDRESSES (0XC00002F1). The full message reads: "Unable to accomplish the requested task because the local machine does not have any IP addresses."

I've seen this most often after a laptop wakes from sleep or hibernation. The network adapter comes back, but the DHCP lease doesn't. It also shows up when you switch between Wi-Fi and Ethernet, or if a VPN client decides to mess with your adapter settings. One real-world trigger: you plug your work laptop into a docking station, and the Ethernet adapter shows up, but Windows doesn't grab an IP from the router.

Why It Happens

It's simple: the local machine literally has no IP address assigned to any active network adapter. That could mean:

• The DHCP client didn't renew the lease.
• The network adapter driver is glitched.
• Your IP configuration is set to static but the values are blank or wrong.
• Windows Network Location Awareness (NLA) service isn't happy.

In 9 out of 10 cases, it's a transient DHCP issue. The router thinks the lease expired, and Windows didn't request a new one. The fix is almost always a quick adapter reset or a DHCP renew.

Quick Fix: Reset the Network Adapter (Works Most of the Time)

1. Open a command prompt as Administrator. Press Win + X and choose Terminal (Admin) or Command Prompt (Admin).
2. Run these commands one by one:
   

   ipconfig /release
   ipconfig /renew
   ipconfig /flushdns
   

3. If /renew hangs, your DHCP server isn't responding. That's rare—but if it does, skip to step 3.
4. Now reset the network stack:
   

   netsh int ip reset
   netsh winsock reset
   

5. Restart your PC if you ran the netsh commands. Otherwise, ipconfig /renew should have done it.

If That Didn't Work: Disable and Re-enable the Adapter

1. Press Win + R, type ncpa.cpl, and hit Enter.
2. Right-click your active connection (Wi-Fi or Ethernet) and select Disable.
3. Wait 10 seconds, then right-click and Enable it.
4. This forces Windows to renegotiate a DHCP lease from scratch. I've used this trick hundreds of times—it's faster than rebooting.

Check Your IP Configuration Manually

Sometimes the adapter is set to a static IP that's wrong or blank. Here's how to check:

1. In the same ncpa.cpl window, right-click the adapter and choose Properties.
2. Double-click Internet Protocol Version 4 (TCP/IPv4).
3. Make sure it's set to Obtain an IP address automatically unless you're on a network that requires static settings.
4. If it's already on automatic, switch to manual, enter 192.168.1.100 (just a placeholder), then switch back to automatic. This can shake loose a stuck configuration.

Still Failing? Check These Three Things

• VPN software: Some VPN clients install virtual adapters that can override your real IP. Disconnect any VPN, then try the release/renew again. If it works, you know the conflict is there.
• Driver rollback: If this error started after a Windows update or driver update, roll back the network adapter driver. Go to Device Manager, find your adapter, right-click > Properties > Driver tab > Roll Back Driver.
• Physical connection: I know it sounds dumb, but I've spent 30 minutes debugging this only to find the Ethernet cable was loose. Wiggle it, try a different port on the router, or reconnect to Wi-Fi.

If none of that works, run sfc /scannow from an Admin command prompt. It'll check for corrupted system files, which can sometimes cause weird network behavior. That's rare, but worth a shot before you reinstall drivers.

For what it's worth, I've never seen this error come back once you fix the DHCP lease. If it does keep appearing, your router might be the problem—try power-cycling it. Unplug for 30 seconds, plug back in, and let everything reconnect.